STEP 1 – Connect to your modem via Wi-Fi or Ethernet
Ensure that Wi-Fi is enabled on the device you are using to access your modem (e.g. computer/laptop/smartphone/tablet). If you are using a smartphone or tablet, you should turn off your mobile data connectivity or any hotspot connection during this process.
Connect to the Wi-Fi/Wireless network of the NETGEAR Nighthawk D7000 modem on your computer/laptop/smartphone/tablet. To connect to the Wi-Fi network of the NETGEAR Nighthawk D7000 modem, locate the Wi-Fi network name being broadcast by the modem from your device (e.g. computer/laptop), select this network, then enter the password for this network when prompted.
If you are unsure of the Wi-Fi password, this will be printed on the sticker on the back of the NETGEAR Nighthawk D7000, underneath the barcodes.
PLEASE NOTE: YOU DO NOT NEED TO HAVE A WORKING INTERNET CONNECTION TO CONNECT TO THE WI-FI OF THE NETGEAR NIGHTHAWK D7000 MODEM OR ACCESS THE MODEM GATEWAY PAGE.
Alternatively, you can plug in an RJ-45 Ethernet cable from your computer or laptop to one of the four (4) yellow Ethernet ports on the back of the NETGEAR Nighthawk D7000 modem.
STEP 2 – Log in to your modem
IMPORTANT: Before you attempt to log in to the NETGEAR Nighthawk D7000 modem via a wireless device, please remove the Ethernet (RJ-45) cable from the back of the modem. The only cable that should be connected is the power supply.
Open your web browser (e.g. Google Chrome/Internet Explorer/Mozilla Firefox/Microsoft Edge), enter 192.168.0.1 into the address bar and press Enter.
If successful, a login box or window should appear asking for a username and password. If the login box or window does not appear, you can try www.routerlogin.net instead of 192.168.0.1.
Enter ‘admin’ for the username and ‘password’ for the password.
If the above login doesn’t work, the password will be printed on the sticker on the back of the NETGEAR Nighthawk D7000 modem. Enter this password.
STEP 3 – Enter the Moose Mobile settings into your modem
Once you have logged in, the next set of instructions may differ depending on whether your NETGEAR Nighthawk D7000 modem is brand new, or if the modem has been used previously.
You should see two tabs located in the top-left corner of the page showing ‘BASIC‘ and ‘ADVANCED‘. Click ADVANCED.
You will then see a list of options on the left side of the page. Click ‘SETUP‘. Then click ‘WAN SETUP‘.
Change the WAN Preference field to ‘MUST USE ETHERNET WAN‘, then press the green APPLY button. The modem will then reboot, please allow a few minutes.
After allowing the modem to reboot, you should see two tabs located in the top-left corner of the page showing ‘BASIC‘ and ‘ADVANCED‘. If you have been logged out of the page follow steps 1 and 2 again to get back into the NETGEAR modem page.
Click BASIC. You will then see a list of options on the left side of the page. Click ‘INTERNET‘.
This should now open up a page on the right side of the screen titled INTERNET SETUP. There will now be multiple options presented. You will need to enter/select these options as follows:
Select Country: Australia
Select Internet Service Provider: Other
Transfer Modem: This should be greyed out/not selectable
DSL Mode: This should be greyed out/not selectable
Enable this interface: Ticked (Enabled)
Use VLANID: Unticked (greyed out/not selectable)
Does your connection require a login: Yes
Encapsulation: PPPoE (PPP over Ethernet)
—
Login: [USERNAME]@moosemobile.com.au (your Moose Mobile service username would have been emailed to you during the order process)
Password: moose[YEAR OF BIRTH] (your Moose Mobile service password would have been emailed to you during the order process – this is NOT the same password as your Moose Mobile customer portal login)
Leave all other options as they are and press the ‘APPLY‘ button at the top of the screen.
STEP 4 – Plug your modem into the nbn® device
You now need to plug your NETGEAR Nighthawk D7000 modem into your nbn® device using an RJ-45 Ethernet cable.
One end of the Ethernet cable needs to be plugged into the red port labelled INTERNET on the back of the modem and the other end into the active port on your nbn® device – this will either be a numbered UNI-D port (such as UNI-D 1, UNI-D 2 etc.) or a GATEWAY port.
If you are unsure which port to plug into on your nbn® device, first try UNI-D 1 and then move your way up until you have success. If you have any trouble please contact us on 1300 566 673 and we can provide the required port by looking up your nbn connection.
If you have configured and plugged in your router correctly, the Internet light on the front of your modem (highlighted in the image below) should illuminate. This may take up to five (5) minutes.
If the Internet light does not illuminate after five (5) minutes, please contact our support team on 1300 66 55 75 for further troubleshooting.